Presentamos el FibeAir IP-20S de Ceragon: optimice su infraestructura de backhaul inalámbrica y aproveche un sistema operativo único y habilidades comunes en todos los productos de la plataforma IP-20.
Infraestructura compacta y económica
El FibeAir IP-20S Assured es un conjunto de nodos de retorno inalámbrico compacto para exteriores que lo ayudará a enfrentar una amplia variedad de desafíos durante la implementación de su red, mientras mantiene sus datos seguros y su servicio disponible. Ya sea que su desafío sea establecer una conectividad rentable a los sitios periféricos, reducir las tarifas de licencia de espectro o reducir sus gastos relacionados con la energía, FibeAir IP-20S Assured es la solución para usted.
• Nodo de radio de un solo núcleo
Conmutador Ethernet integrado, compatible con MEF Carrier Ethernet 2.0, preparado para MPLS-TP
• Alta capacidad de radio y eficiencia espectral
Modulación hasta 2048QAM
• Plataforma multipropósito, ideal para escenarios de implementación versátiles
Factor de forma compacto, de fácil implementación en ubicaciones urbanas y rurales
• La alta granularidad del servicio permite la implementación de nuevos modelos comerciales.
Gestión inteligente centrada en el servicio que utiliza QoS jerárquica y capacidades avanzadas de OA&M
• El sistema operativo común y el motor definido por software simplifican la modernización de la red
CeraOS unificado en toda la plataforma FibeAir IP-20 Impulsado por un procesador de red programable
| PRODUCT | |
| Model/Part# | See table below for full set of Model and Part Numbers |
| SPECTRUM | |
| Channel Spacing | Configurable on 5 MHz increments |
| Frequency Range | 5150 - 5970 MHz (exact frequencies as allowed by local regulations) |
| Channel Width | 5 I 10 I 20 I 40 MHz |
| INTERFACE | |
| MAC (Media Access Control) Layer | Cambium proprietary and optionally standard 802.lln |
| Physical Layer | 2x2 MIMO/OFDM |
| Ethernet Interfaced | 100/lOOOBaseT, rate auto negotiated, 802.3at compliant |
| Powering Methods Supported | 56 V PoE (included), standard 802.3at PoE Supply, or CMM4 with 56 V and 5 pin to 7 pin cross over cable adapter |
| Protocols Used | IPv4/IPv6 (Dual Stack), UDP, TCP, ICMP, SNMPv2c, NTP, STP, IGMP, SSH |
| Network Management | IPv4/IPv6, HTTPs, SNMPv2c, SSH, Cambium Networks CnMaestro™ |
| VLAN | 802.lQ with 802.lp priority |
| PERFORMANCE | |
| Subscribers per Sector | Up to 120; Lite version limited to 10 |
| ARQ | Yes |
| Nominal Receive Sensitivity (w/FEC) @20MHz Channel | MCSO = -93 dBm to MCS15 = -69 dBm (per branch) |
| Nominal Receive Sensitivity (w/FEC) @40MHz Channel | MCSO = -90 dBm to MCS15 = -66 dBm (per branch) |
| Modulation Levels (Adaptive) | MCSO (BPSK) to MCS15 (640AM 5/6) |
| GPS Synchronization | Yes, via internal GPS or CMM4 with 56 V and 5 pin to 7 pin cross over cable adapter |
| Quality of Service | Three-level priority (Voice, High, Low) with packet classification by DSCP, COS, VLAN ID, IP & MAC Address, Broadcast, Multicast, and Station Priority |
| Transmit Power Range | 0 to +30 dBm (combined, to regional EIRP limit) (1 dB interval) |
| RECOMMENDED ANTENNAS | |
| Sector Antenna | ePMP Sector Antenna (C050900D021A) available |
| ePMP 2000 Smart Antenna | ePMP 2000 Smart Antenna (C050900D020A) available (complimentary; does not replace Sector Antenna) |
| PHYSICAL | |
| Sector Antenna Connection | 2 x 50 ohm, RP (reverse polarity) SMA |
| Beamforming Antenna Connection | 2 x 50 ohm, RP (reverse polarity) SMA, DC coupled (powering antenna) |
| GPS Antenna Connection | 1 x 50 ohm, RP (reverse polarity) SMA |
| Surge Suppression | 1 Joule Integrated |
| Environmental | IP55 |
| Temperature | -30°C to +55°C (-22°F to +131°F) |
| Power Consumption | 20 W Maximum [1] |
| Input Voltage | 44 V to 59 V |
| Weight | 0.7 kg (1.54 lbs.) without brackets |
| Dimensions | 125 x 210 x 37 mm (4.9 x 8.3 x 1.5 in.) without brackets |
| Pole Mount Included | Yes |
| Environmental Cover Included | Yes |
| SECURITY | |
| Encryption | 128 bit AES (CCMP mode) |
| CERTIFICATIONS | |
| FCCID | Z8H80FT0020 |
| Industry Canada Cert | 109W-0020 |
| CE |
EN 301 893 V2.1.1 EN 302 502 V2.1.1 |
Notes:
[1] The maximum power consumption of the Access Point is the same regardless of whether the optional Smart
Beamforming Antenna is equipped or not. This is because the Beamforming Antenna draws its power during the uplink
cycle when the Access Point power consumption is not at its maxium.
Artículos relacionados
